| INSPECTION ID
|
DATE
|
DESCRIPTION
|
COMMENT
|
VIOLATION ID
|
VIOLATION CODE
|
VIOLATION_COMMENT
|
| -1191951268
|
2013-05-14
|
|
My inspection of the well and surface facility found a truck without an Underground Injection Control number. The truck was owned and operated by Liquid Luggers. Dave Jenkins was notified. The truck driver was instructed to wait on location, until the truck was properly labeled.
|
|
|
|
| -145081195
|
2012-10-16
|
|
My inspection of the injection facility and well found no violations. The pump was operating, while the pressures were gauged.
|
|
|
|
| -1463080583
|
2012-06-19
|
|
My inspection of the well and facility found no violations.
|
|
|
|
| -1472625338
|
2013-04-04
|
|
My inspection of the injection facility and well found no violations. The pump was operating at the time pressures were gauged.
|
|
|
|
| -158305718
|
2014-06-13
|
|
The well was found operating over the maximum allowable injection pressure. Matt Kleese was notified in person. The pump rate was slowed, lowering the injection pressure.
|
|
9-3-07(D)
|
|
| -1696987330
|
2013-01-09
|
|
My inspection of the injection facility and well found no violations.
|
|
|
|
| -188703593
|
2011-08-18
|
|
The owner has applied to convert the well to a saltwater injection well. The well site was inspected as part of a field review. There are no water wells or bodies of water within close proximity to the proposed location of surface facilities. The inspe
|
|
|
|
| -1894502968
|
2012-07-03
|
|
My inspection of the well site found no violations at the time.
|
|
|
|
| -2132087981
|
2012-07-20
|
|
My inspection of the well site and injection facility found no violations.
|
|
|
|
| -669971554
|
2012-12-05
|
|
My inspection of the injection facility found no violations. I took a water sample from a brine hauler. The sample was sent to the Cambridge Lab for analysis.
|
|
|
|
| 1300289555
|
2013-05-14
|
|
I completed a salt water injection well inspection with ODNR Inspector Steve Ochs. My inspection found the tubing had 1130 psi and the 4.5" had 0 psi. The injection facility was in good operating condition with no water or oil surrounding the diked tanks.
|
|
|
|
| 1318336643
|
2011-10-11
|
|
Parmaco tension packer installation was witnessed.
|
|
|
|
| 1318429191
|
2011-10-12
|
|
Fresh water, with corrosion inhibitor, was pumped into the tubing/casing annulus. A Parmaco tension packer was set. The well failed to pass the Mechanical Integrity Test.
|
|
|
|
| 1320080398
|
2011-10-31
|
|
Contractor attempted to set the packer.
|
|
|
|
| 1404816190
|
2011-10-31
|
|
A mechanical integrity test was performed on this well and 1180 PSI was placed on the tubing/casing annulus. There was a decline in pressure of approximately 5 PSI observed during the 15 minute test period.
|
|
|
|
| 1496083948
|
2012-09-04
|
|
|
|
|
|
| 169837762
|
2012-02-01
|
|
A trench was dug to tie the oil tank containment dike into the drainage system.
|
|
|
|
| 171751610
|
2011-10-03
|
|
An injection test was performed on this well. Approximately 400 barrels of fluid were pumped in 1 hour and 3 minutes. The average rate was 6.35 barrels per minute. The maximum pressure was 875 PSI. The pressure at the conclusion of the test was 600 PSI. The pressure was at 525 PSI, 5 minutes after shutdown.
|
|
|
|
| 329206871
|
2012-03-12
|
|
My inspection of this site found the dike wall was being constructed. There were no violations noted at the time of inspection.
|
|
|
|
| 517272107
|
2013-08-20
|
|
There were no violations at the time of inspection.
|
|
|
|
| 556276720
|
2014-03-17
|
|
My inspection of the well found no violations at the time.
|
|
|
|
| 562822320
|
2012-08-14
|
|
My inspection of the well site and injection facility found no violations.
|
|
|
|
| 59604026
|
2013-10-10
|
|
No violations were found at the time of inspection.
|
|
|
|
| 707560555
|
2011-10-19
|
|
A Mechanical Integrity Test was performed. The test failed.
|
|
|
|
| 748827000
|
2012-01-10
|
|
The pad was being poured for the tank battery. All conditions were acceptable.
|
|
|
|
| 803709669
|
2012-06-06
|
|
My inspection of this well site found no violations at the time.
|
|
|
|
| 959693422
|
2011-10-26
|
|
A mechanical integrity test was performed on this well and 1235 PSI was put on the tubing/casing annulus. There was a decline in pressure of approximately 5 PSI observed during the 15 minute test period.
|
|
|
|