X

Track changes made to this page

If you find this page useful and would like to be notified of changes made to this page, start by inputting your email below.



Privacy policy
Close this window

powered by ChangeDetection

34-133-23614

Well Details

Well ID: 34-133-23614
Loading map...
County:
Municipality:
Operator Name:
Well Pad ID:
Farm/Lease Name:
First Permit Date:
Last Permit Date:
Spud Date: 1987-10-06
Unconventional:
Horizontal:
Producing: No
Violations: 12
Latitude: 41.1051427783
Longitude: -81.3582279968

Production Data

PERIOD GAS QUANTITY GAS PRODUCTION DAYS CONDENSATE QUANTITY CONDENSATE PRODUCTION DAYS OIL QUANTITY OIL PRODUCTION DAYS

Waste Data

PERIOD TYPE QUANTITY UNITS DISPOSAL METHOD WASTE FACILITY PERMIT ID WASTE FACILITY NAME FACILITY CITY FACILITY STATE

Inspection Data

INSPECTION ID DATE DESCRIPTION COMMENT VIOLATION ID VIOLATION CODE VIOLATION_COMMENT
-1048891859 2010-12-16 Quarterly status check inspection found no violations at this time. Injection pressure at the wellhead (970 psi) exceeded the allowable (850 psi) and the company shut the injection pump down. The pressure gauge at the injection pump indicated a pressure closer to 900 psi. The well reportedly is on vacuum at the start of the day and quickly builds to the maximum allowable injection pressure. The pressures need to be checked more often.
-112241534 2009-08-19 Quarterly status check inspection found no violations at this time.
-1140843101 2010-02-16 Quarterly status check inspection found the injection pressure exceeded the maximum allowable of 850 psi by 90 psi. I directed the on site operator to shut the system down and monitor the injection pressures more often to avoid any excess values. According to the operator, the well starts on vacuum and pressures slowly build during the injection day.
-1188813984 2006-05-03 Status check inspection found no violations at this time. I did call Pander and asked them to either re-paint or replace the ID sign.
-1207113919 2007-05-14 When the well was inspected on May 9, the company gauge on the injection side could not be removed and indicated that the injection pressure was 1000 psi. The maximum approved injection pressure is 850 psi. I notified Pander of the problem. On May 14, the injection pressure was 820 psi and the company gauge had been replaced.
-1229566074 2006-02-08 Status check inspection for this salt water disposal well. No violations at this time.
-1246444897 2012-12-19 My inspection of the injection facility found no violations. I took a water sample from a brine hauler.
-1252044596 2007-08-24 Quarterly status check inspection found no violations at this time. I spoke with the onsite operator about the maximum injection pressures allowed for this well. He said that pressures have been higher than usual lately and that Pander may be planning to acidize the well.
-1291640453 2012-11-01 My inspection of the injection facility and well found no violations.
-1337326906 2012-08-16 My inspection of the well site and injection facility found no violations.
-1350632747 2013-11-20 No violations were found at the time of inspection.
-1387849805 2013-09-03 My inspection of the well and injection facility found no violations.
-1535445549 2008-11-18 Quarterly status check inspection found no violations at this time.
-154205112 2007-02-12 Quarterly status check inspection found no violations at this time.
-1583010141 2009-11-19 Quarterly status check inspection found no violations at this time.
-1621016030 2003-02-28 Status check inspection of salt water injection well. The system was not running during the inspection. No violations at this time. 9-3-05(A)3
-1710782553 2010-08-24 The requested changes were made to the wellhead and the injection pressure was recorded.
-1785547444 2014-05-22 A mechanical integrity test was performed on the new injection line. The injection line held 980 psi. for 15 minutes without any loss. The soil remediation was completed and the area was graded.
-1853584109 2006-07-22 Pander removed the packer that was set two weeks ago after there were indications that it was failing during brine injection. The packer had been set in compression and passed the MIT performed on July 8. Pander again ran a rebuilt Arrow Lockset packer in compression. The packer was set at 3712'. The MIT was condudcted at 940 psi with no loss of pressure after 15 minutes. The test passed.
-244293268 2014-06-04 There were no violations at the time of inspection.
-265559582 2004-11-18 Status check inspection - no violations at this time.
-277579850 2003-10-03 Follow up UIC inspection to check pressures and to confirm that the valve on the injection side had been replaced. No violations at this time.
-33243698 2009-03-20 The valve on the 8-5/8" annulus has been replaced, as requested.
-353724650 2003-09-03 Status check inspection - no violations at this time.
-362248018 2005-06-01 Status check inspection for this salt water disposal well. No violations at this time.
-422238234 2005-08-25 Status check inspection - no violations at this time.
-433447773 2010-08-17 The quarterly status check inspection found a discrepency between the wellhead pressure gauge and the gauge on the injection pump. I asked Pander to replace the pressure gauge on the wellhead and place a tapped bull plug and needle valve for the MRM gauge off of the wellhead. I will check the pressures after this request has been honored.
-458804002 2013-12-27 No violations were found at the time of inspection.
-574805034 2014-05-07 There were no violations found at the time of inspection.
-637314486 2014-06-19 An inspection of the well and injection facility found no violations.
-663199401 2012-03-06 The injection pressure was exceeding the maximum allowed. The well owner shut down immediately. 9-3-07(D)
-682073966 2008-05-12 Quarterly status check inspection found no violations at this time.
-687040337 2004-02-11 Status check inspection - no violations at this time. 790# injection and 900# annulus.
-71014784 2004-08-10 Status check inspection - one of the brine tanks had been overfilled and impacted the tank battery. Both free oil and brine were still present on the dike floor. I contacted Ray Pander and informed him of the violation. A new check valve had been installed and did not have a needle valve to check the injection pressure. 9-3-04(A)
-796359438 2009-06-10 The tubing is out of the hole and they are waiting for a service rig to swab the well. Pander is still trying to improve the injection characteristics of this well. A MIT will be completed after the tubing and packer are placed back in the hole.
-806253113 2011-08-03 I performed the quarterly UIC test on the annulus and the injection. The well was running and the maximum pressure was exceeded by 90psi. I had the well shut in.
-83764055 2009-02-24 Status check inspection found no violations at this time. I called Pander and requested that they change the 2" ball valve on the annulus. I could not open it to check annular pressure.
-902973724 2013-10-09 No violations were found at the time of inspection.
1093672158 2011-05-17 Quarterly status check inspection found that the permitted maximum injection pressure (850 psi) had been exceeded and the well was injecting at 1080 psi. I ordered the well shut in and the injection pump shut down. I also advised Ray Pander that if the higher injection pressures are due to injecting fresher water, he may consider applying for a fluid density modification to permit a higher injection pressure. I also advised him that additional reporting and monitoring requirements will apply if he chooses to pursue this modification.
1111441938 2004-05-04 Status check inspection of this salt water disposal well. No violations at this time.
1152534634 2006-07-08 Pander changed out the tubing string and replaced the packer in this well. The new tubing string is 2-3/8" upset and the packer is a rebuilt Arrow Lockset. Mixed five gallons of inhibitor in 80 bbl of fresh water and circulated to surface. The new packer was set in compression at 3738'. After setting the packer, pressured up the annulus to 1050 psi and held for 15 minutes. The test passed.
1152798167 2006-07-10 The injection system has been re-connected and started. So far injection pressures have been high. I reminded the driver on site that the maximum injection pressure is 850 psi.
1154391870 2006-07-25 The MIT was successfully completed on 7/22 and the well is now back in use. The injection pressures are near 800 psi and the annular pressure is 150 psi.
1216i108 2001-11-28 Arrived on site as the well was shut down. Pressures on the tubing and annulus are equal. Discussed with the well tender. Waited twenty minutes then turned the pump back on. Pressres went from 760psi to 820psi on both. Told the tender to shut down and determine the cause before injecting again. The tender called in to the office once to notify Ray or Allen, then again to vedrify that they were contacted. THE COMPUTER PROGRAM WILL NOT PERMIT THE ADDITION OF THE CODES VIOLATED. 1509.03 AND OAC 1501:9-3-05 ?.
1216i14 2001-08-21 Inspection this date revealed no violations. Last inspection date: 05-02-2001
1220536557 2008-08-14 Quarterly status check inspection found no violations at this time. The well continues to operate at the maximum allowable injection pressure.
1221795349 2006-12-07 Quarterly inspection of this salt water disposal well found no violations at this time.
1231266086 2014-05-21 The well owner reported an injection line leak. An inspection found a brine impacted area approximately 50 feet by 100 feet. A trench was cut down slope from the injection line and wellhead. The area was flushed with fresh water and the run off was collected in the trench, which was lined with plastic. 9-3-04(A)
1234072880 2003-06-17 UIC status check inspection - no violations at this time.
1243433047 2009-05-26 J-Well's service rig pulled the tubing and packer. I met with R.C. Pander on the site and discussed the well. The injection well is shut down until it can be treated on June 4th or 5th. I called Bob Worstall and informed him of the schedule change.
1247599445 2009-07-08 Pander removed the tubing string and packer from this well in order to treat the well for bacteria, crude oil and parafin. The tubing was out of the hole for approximately seven weeks while various treatment proposals were evaluated. The well was ultimately treated with bacteriacide and "Salty Dog" in an attempt to lower injection pressures. On 7/8 Hagen Well Service ran 117 joints of 2-3/8" tubing and two pup joints with a Weatherford Arrow Lockset packer (3692') back in this injection well. Five gallons of inhibitor was mixed with 80 bbl of fresh water. 60 bbl of this mixture was pumped down the annulus between the tubing and the 4-1/2" production casing. The packer was then set in compression. The MIT was completed with an initial pressure of 1015 psi, five minute pressure of 1015 psi, ten minute pressure of 1015 psi and fifteen minute pressure of 1005 psi. After passing the MIT, the annular pressure was manually lowered to 200 psi. The rig was released and moved off location. On 7/9, the annular pressure was 0 psi and the well was on vacuum. As Pander starting injecting, the annular pressure increased to 300 psi and the injection pressure increased to approximately 800 psi. On 7/10, both the annulus and the tubing were on vacuum. Operations were terminated pending evaluation. On 7/14, Moore Well Service rig was on site to correct the pressure leak. While tightening the tubing string by rotation, the packer unseated and another MIT was completed. The initial pressure was 1020 psi, five minute pressure of 1015 psi, ten minute pressure of 1015 psi and fifteen minute pressure of 1015 psi. The second MIT passed.
13079107 2002-04-24 Well was not running at time of inspection. NO VIOLATIONS.
1345574831 2012-07-26 My inspection of the well site and injection facility found no violations. The pump was off at the time.
1405359860 2014-05-19 An inspection of the well and injection facility found no violations.
1506088590 2004-08-20 Spill clean-up is beginning by flooding the dike with hot water and steam washing the stone. 9-3-04(A)
1534636428 2012-06-15 The injection system was not running at the time of the inspection. My inspection found no violations at the wellhead or at the brine tank battery.
1640620463 2007-05-09 Quarterly status check found that the injection pressure (1000 psi) exceeds the maximum allowable of 850 psi. I could not remove Pander's gauge to verify the pressure using the MRM gauge. The injection pressure therefore was obtained from their gauge. I contacted Pander and requested that they shut the system down until the injection pressure is controlled and the accuracy of the gauge is verified.
164765471 2008-02-25 Quarterly status check inspection found no violations at this time. On Monday March 3, Producers Services is scheduled to inject 3000 gallons of 15% acid to try and open up the perforations and reduce the overall injection pressures.
1804986150 2014-03-21 Pressure readings were taken, while the pump was operating. There were no violations at the time of inspection.
1868904508 2005-02-25 Status check inspection of this salt water disposal well and storage system. No violations at this time.
2026418893 2010-05-05 Quarterly status check inspection found no violaitons at this time.
2034757622 2014-04-18 The pump was shut off approximately half an hour prior to inspection. There were no violations at the time.
2045054076 2002-11-13 Injection pressure 150 PSI. System was not running. System needs to be checked when running to resolve N.O.V. 9-3-05(A)3
2135549648 2002-10-28 FOLLOW UP TO NOV # 2154i536 Injection well was running at the time of the inspection. Injection pressure was 920 PSI. This exceeded the allowable injection pressure of 850 PSI. The well was immediately shut down at the Inspector's request by the operator (Jeff) at the site. Inspect 9-3-05(A)3
2154i188 2002-05-30 Water in tank battery is gone. Crude oil staining exists inside tank battery dike at previous water line.
2154i239 2002-06-24 4-29-02 Called Pander Trucking and informed them that there was crude oil on the water within the tank battery dike and requested it to be cleaned up. 5-28-02 Water in the tank battery dike was gone, but there was crude staining on the soil within the tank battery dike. 6-24-02 System was not running. Crude oil was floating on the water within the tank battery dike and the soil staining was still present. The dike area needs to be cleaned up. Ray Pander Trucking 330-654-2500. 9-3-04(A)
2154i310 2002-07-23 Tank battery dike has not been cleaned up. System was not running. 9-3-04(A)
2154i382 2002-08-20 N.O.V. RESOLVED. System was not running. NO VIOLATIONS.
2154i47 2002-02-25 Well not running the day of the inspection. No Violations.
2154i536 2002-10-28 Injection well was running at the time of the inspection. Injection pressure was 920 PSI. This exceeded the allowable injection pressure of 850 PSI. The well was immediately shut down at the Inspector's request by the operator (Jeff) at the site. Inspector Claus informed Pander Trucking (Alan) of the violation. 9-3-05(A)3
375283723 2012-12-10 The well owner performed a mechanical integrity test on the well. My inspection of the injection well found no violations.
468476655 2013-06-17 My inspection of the well and surface facility found no violations.
485125670 2005-12-01 Status check inspection of this salt water injection well. No violations at this time.
507242629 2011-02-24 Quarterly status check inspection found no violations at this time. Injection pressures remain at the maximum allowable limits.
574142539 2006-07-05 J-Well is on site to replace the tubing string and the packer in this well. No violations at this time.
63347918 2004-08-26 The violation has been corrected 9-3-04(A)
644171734 2007-12-03 Quarterly status check inspection found no violations at this time.
676108043 2001-11-28 FOLLOW UP TO NOV # 1216i108 Arrived on site as the well was shut down. Pressures on the tubing and annulus are equal. Discussed with the well tender. Waited twenty minutes then turned the pump back on. Pressres went from 760psi to 820psi on both. Told the tender to shut down and de
749327128 2012-03-08 My inspection of this well site found thet the pressure on the tubing was zero, the pump was shut off and the gate was locked.
834421028 2013-03-08 My inspection of the injection facility and well found no violations. The pump was off at the time.
918916743 2009-07-07 Hagen Well Service is on site to reset the packer and conduct the mechanocal intregity test. Both are scheduled for 7/8 at approximately 9:00 am.
932523482 2012-07-18 My inspection of the well site and injection facility found no violations. The pump was off at the time.
979546307 2011-11-01 I performed the quarterly UIC test on the annulus and the injection. The well was not running. There were no violations at this time.
iTOMK000078 1999-05-27 9-1-07
PL5850 Preliminary Restoration done information from Data Point
UIC1105 1991-05-30 1509.03 RULES & REG. ENFORCE
UIC1106 1991-05-30 1501:9-1-07 CONTAM. & POLLUTION
UIC1107 1991-05-30 1501:9-03-05 (A) (6)
UIC1215 1991-12-17 1509.03 RULES & REGULATIONS
UIC1701 1998-02-03 1501: 9-3-07 (D) EXCEEDED MAX.INJ PSI
UIC1702 1998-02-03 1509.03 EXCEED MAX.INJ PSI
UIC1707 1997-12-09 1501: 9-3-07 (D) EXCEED MAX INJ PSI
Retrieved from "https://wellwiki-prod.cloud.arc.gwu.edu/index.php?title=34-133-23614&oldid=2370295"